Kitchen cabinet instal: what to do with base board?
fatboysam
6 years ago
Featured Answer
Sort by:Oldest
Comments (8)
PPF.
6 years agofatboysam
6 years agoRelated Discussions
Ideas on updating/replacing the veneer trim under kitchen cabinets
Comments (12)I would seriously consider replacing the cabinets before putting a new granite countertop on them. The problem is that no one will remove the countertop at a later date if you want to change the cabinets, due to the possibility of breakage. The only choice you will have then is a reface. Adding new doors, drawer fronts, and veneered sides is just a facelift. You could also add new hardwood drawers with undermount cushion close slides, but by the time you do this if will be the same cost as new cabinets now. The cabinets you have now, frameless, particle board sides are notorious for having the hinge screws strip out the particle board they are attached to. Since you can't put a longer screw in them, because the material is only 3/4" of an inch thick you have a problem. You also can't put a wider screw in them because it won't fit through the pre-drilled holes in the hinges....See MoreKitchen base
Comments (1)What did you decide to do? I'd love to see photos if you have any available....See MoreThe HouzzAU Queenslander club
Comments (2)I LOVE OLD QUEENSLANDERS.....emphasis on O L D! What a sight, a tall Queenslander...having come into being because of the heat in this State and therefore on tall and not so tall piers...I LOVE these houses but with one exception...and probably because in those days ther were no such things as... LIFTS! Nobody thought of the older Queenslander human whose hips and knees are worn out from hard work on the land..or for the little kids and toddlers.....STAIRS, STAIRS and more STAIRS! Beautiful gracious staircases....but.... Recently a young enthusiastic couple built a magnificent looking replica old Queenslander right across from my place. I watched it go up...and so did the rest of the neighbourhood...well, not criticising the modern builder but I'd rather have a genuine old Queenslander put together with hammer and iron nails! STAIRS seemed to have been made into a feature. The land overlooks a waterway that is prone to flooding so the piers had to be quite high....and that meant more treads! I think that maybe the builders were unaware of the need for a landing every...is it eight? steps? The back steps are straight up the rear of the house...no landings....OOOFFF going to welcome your new neighbiurs! I would not build a replica Queenslander but if I couldn't help myself I'd install A LIFT and I would invent a feature for going up and down .for the children...and I'd get my inspiration from some of the great Theme Parks that have to comply to strict safety standards.....Then and only then would I build a replica Old Queenslander...But I'd prefer A REAL ONE! .It has been my experience that replicas do not have the strength of the enormous oldies. For example: Show me a replica Queenslander with iron cyclone bolts securing the floor of the house to the piers. Show me a replica Queenslander where every VJ board in the walls and ceilings is held to the next with hidden nails? Show me one where the framework is all tongue and groove each piece locked into the other.....that cannot be achieved anymore because timbers are not seasoned for between 30-50 years and such building methods would weaken the structural timbers used today...so said the builder who added a veranda to my old place. He took photographs of the joinery! I LOVE OLD QUEENSLANDERS...But I'd only buy a really old one and renovate it using old methods and as much old timber as possible...and I'd add a LIFT and a kids "upper and downer" if the steps were to be high. One thing above all would deter me from building one from scratch....the unavailability and the expense of genuinely old timber...if it could be sourced.. A replica would never match the longevity and the methods of construction of the old ones. Those times are gone! Those homes can never be repeated...only replicated and its not the same by any bash of the nail. You can't buy those nails anymore and its impossible to hire a crew as large as a swarm of ants to build an old Queenslander from scratch. We just do not build like that these days. Meaning no disrespect to the skilled modern day builder who does marvellous things for the modern day.....its impossible to build a genuine old Queenslander for many reasons. LOVE and ADMIRE and CHERISH the old Queenslander, BUY ONE if you can and restore it as genuinely as possible. We'll never see its like again from any perspective....See MoreNeed help to determine where to place my inbuilt oven
Comments (14)Hi Fred, Thanks for the want of the precise measurements. The U shape area in my kitchen is 64" - 104 - 99" (left - centre - right). Height of the kitchen area is 107". The wall with the fridge has total length of 99" Fridge is 32" wide, 29" deep, 73" high (I bought this fridge on a good bargain but realized it was slightly oversized in this kitchen area, but got to live with it now) The wall beside the fridge is 23" deep I know some gap has to be left between this wall, the fridge and the wall mounted/countertop cabinets for ventilation I guess. So I'd say the cabinets on this wall will have a length of only 63"/64"? The microwave is 18.5 wide, 13" deep, 10.5" high The oven is 24" wide, 24" deep, 24" high. The wall next to the fridge which will have this feature cabinet 42" wide, 110" high which is next to the main door. I'm thinking the feature wall is kind of plain, but it covers up where the fridge is sticking out....See MoreUser
6 years agolast modified: 6 years agoHome Ideations LLC
6 years agoPPF.
6 years agofatboysam
6 years agoGannonCo
6 years ago
Sponsored
Hal Braswell Consulting